Titan Products Now Available from IBC

Titan Products Ireland announcement showing a TP-710 fan coil controller and Gen 3 room sensor, now available from IBC.

IBC now supplies Titan Products’ HVAC controls and sensors, extending its offering for BMS engineers, system integrators and mechanical contractors.

The initial focus is on TP-710 fan coil controllers, rotary room interfaces and Gen 3 room temperature, humidity and CO₂ sensors, supported by Titan’s wider plant sensor range.

TP-710 fan coil controllers

The TP-710 range covers two-pipe and four-pipe fan coil applications, with BACnet/IP and BACnet MS/TP models.

Titan TP-C-710-IP BACnet/IP and TP-C-710 BACnet MS/TP fan coil controllers shown side by side.
TP-C-710-IP with BACnet/IP communication, left, and TP-C-710 with BACnet MS/TP communication, right.

Options include controllers for EC fan control and an interlocked relay model for three-speed fans. Titan’s ToolBox commissioning platform supports controller discovery, configuration and copying of control profiles.

Controller selection starts with the fan coil arrangement, fan and valve control requirements, and the project’s BMS network.

Controller datasheets

Rotary room interface for TP-C-710

Which fan coil settings should occupants be able to adjust? The Titan TP-UI-RO rotary room interface provides local setpoint, fan speed and mode adjustment, with the available menus and setpoint range configured to suit the application.


White Titan TP-UI-RO rotary room interface showing temperature, humidity and optional CO₂ readings, with blue HALO indication.
Titan TP-UI-RO rotary room interface, shown with optional CO₂ sensing. View the full set of display examples in the rotary interface datasheet.

The interface combines a rotating dial, push-to-select operation and a colour display with built-in room sensing. Engineers can configure the interface locally through its engineer menu or over BACnet.

  • Defined setpoint limits: set minimum and maximum values for local temperature adjustment.
  • Application-specific menus: show or hide fan speed, run mode and comfort mode options to match the installation.
  • Integrated room sensing: temperature and humidity monitoring are standard, with CO₂ monitoring available on the TP-UI-RO-CO2 variant.

When paired with the TP-C-710 BACnet MS/TP controller, a direct Cat 5 connection via Titan’s T-BUS carries power, room measurements and user adjustments between the two devices. The interface takes its power from this connection, removing the need for a separate interface power supply.


Two Titan TP-C-710 fan coil controllers connected to a BACnet MS/TP network, each with a directly connected TP-UI-RO rotary room interface.
TP-UI-RO rotary interfaces connect directly to TP-C-710 fan coil controllers, with the controllers communicating to the BMS over BACnet MS/TP.

Enlarge diagram

White and black versions are available. Selection starts with the room measurements required and the adjustments occupants should be able to make.

Gen 3 room sensors

Titan’s Gen 3 range covers temperature-only, combined temperature and humidity, and combined CO₂, temperature and humidity measurement.

Titan Gen 3 room sensors with white and black housings, including a white sensor with green HALO indication.
Titan Gen 3 room sensors, showing white and black slimline housings and a HALO variant.

Depending on the model, connection options include resistive outputs, analogue signals or BACnet MS/TP and Modbus RTU communication. CO₂ models with HALO indication provide a visible indication of room CO₂ levels.

Sensor selection depends on the measurements required and the available controller inputs or network.

The Gen 3 brochure includes product codes and a comparison of sensing, output and enclosure options.

Plant sensors

The wider Titan offering includes sensors for duct, outside-air, immersion and clamp-on applications, supporting measurement across HVAC plant as well as occupied spaces.

Titan product enquiries

IBC can assist with product selection, pricing and availability. Enquiries can include the application, measurement or control requirements, preferred communication protocol and any known product codes.